How much does it cost to install built in bookshelves?
Table of Contents
How much does it cost to install built in bookshelves?
The cost to have built-in bookshelves installed averages $2,691 or between $1,273 and $4,119 for a carpenter to do the job. If you buy the materials yourself, you can usually get a handyman to install them for $30 to $130 per hour. For high end custom work, expect to spend $150 to $1,200 per linear foot.
Is building a bookshelf easy?
Once you have the lumber, building a bookshelf is a fairly simple woodworking project that you can get done in just a day or two. It’s a low-cost project as well and since the plan is free, you don’t have to worry about busting through your budget.
How many hours does it take to build a bookcase?
This Project Will Work in Any Room. Even though this project isn’t complicated, it’s still going to take you at least 40 hours to build. A bookcase or shelf is an extremely useful home storage system.
Is it hard to build your own shelf?
As far as DIY home projects go, building DIY shelves is not that much harder than putting up premade ones (not to mention how much you will save for way higher quality materials). The best part about creating your own shelving is that you get to pick the style, price of materials, and difficulty.
How deep should bookshelves be?
Shelf depth for a general purpose bookshelf is usually 10 to 12 inches. Shelf spacing will generally range from 7 to 15 inches with 8 to 12 inches being common for bookshelves.
How do you build bookshelves?
How to Build a Bookshelf in 8 Steps
- Step 1: Cut the Legs, Shelves, and Supports. Photo by Kolin Smith.
- Step 2: Attach the Supports to the Legs.
- Step 3: Assemble the Box.
- Step 4: Level the Bookcase.
- Step 5: Plumb the Bookshelf.
- Step 6: Attach the Kick Board.
- Step 7: Scribe the Trim to Fit.
- Step 8: Apply Nosing to Shelf Faces.
How shallow can a bookcase be?
Remember, you want to have a little bit of extra space on the shelf so that the book can sit comfortably on the shelf. Likewise, if you own a lot of mass paperback books that do not measure about four inches, you could get your bookcase down to about six inches.
How deep are built in bookshelves?
11 to 12 inches
Most shelves are built a minimum of 11 to 12 inches deep, but this is your chance to customize: Go for it!
How do you attach a bookshelf to the wall?
Apply wood glue to the support blocks for the center shelf, and set the shelf in position. Drill and countersink pilot holes in the side of the bookshelf, and attach the shelf with 2″ wood screws (Image 2). Be sure to drill the holes in an area that will be covered when the bookshelf is recessed into the wall.
How to build a sturdy bookshelf?
The bookshelves you’ll build must be sturdy and last a long time. You want to make sure that the shelves are cut from quality lumber and composites that do not bend under prolonged weight or warp. Once you’ve selected the wood for your project, the next step is to create the support frame.
How do you make a bookshelf out of baseboard?
Drive the nails through the side panels into the end grain of the bottom shelf. You can repurpose the baseboard for the bookshelf with this step. Cut the baseboard to size and use a miter saw on the ends as necessary. Use wood glue to bind the baseboard to the bottom of the built-in shelves.
How do you measure for built-in book shelves?
The height of your built-in shelves will be 1 inch short of your ceiling. When measuring the height of the shelves, measure from the floor away from the baseboard or moldings. Once you’ve made your measurements, trim and remove baseboards or crown moulding along the length of where you want the bookshelves to be built.